Loading
Bacteria are nature's housekeepers and have been around 3.5 billion years. They are truly amazing, not only are they willing workers who are...
Started by Al Zylstra in General Water Treatment
The Dramm AME HAF fans and PS Speed Controllers can be controlled from an external climate control computer allowing the speed to be varied based on...
Started by Kurt Becker in AME Horizontal Air Flow Fans
Each emitter has a very small number showing flow rate in L/H molded into the plastic near the outlet. However, since January of 2020, the emitters...
Started by Kurt Becker in Pressure Compensated Drip Irrigation
Hello, I purchased two sets of the Dramm easy connect systems from my nursery and I love the easy connections. My problem is that water leaks out...
Started by Anonymous in General
Clean them after every use. That sounds simple. Unfortunately, this is not always done. Spraying is often done late in the day, when people are...
Started by Kurt Becker in Coldfogger
Started by Kurt Becker in Equipment Service
Started by Kurt Becker in General Equipment
Can Bio Insecticides be used in the SVLH 20A fogger? I'm curious about products like Grand Evo, BT, venerate, and regalia. Thank in advance,
Started by evander707 in Autofog
Dramm does not recommend using reverse osmosis water as the carrier when using hydrogen peroxide or peroxyacetic acid (PAA) based products in the...
Because the FM Foamers use compressed air, the volume and pressure must be right for good foam production. The FM Foamers require a minimum of 3 CFM...
Started by Kurt Becker in Foamer
Hello, We have one pulfog k-50 and we used this for apply Rhapsody (Basillus subtilis) in greenhouse. What kind of nozzles do you recommend for...
Started by Hector in pulsFOG
The JETFog nozzle recommended operating pressure is between 50-60psi, if pressure over exceeds the maximum that is recommended this can cause damage...
Started by Unregistered in JetRain/JetFog Nozzles
What is the best and easiest way to remove the nozzle tip of the JETFog nozzle when having to clean or replace?
Started by Andrew Damm in JetRain/JetFog Nozzles
My JETFog nozzle is leaking, can the inside diaphragm be replaced
Some growers have asked about fogging azadirachtin products in the pulsFOG wondering if this requires the BIO units. Azadirachtin is not heat...
Started by Kurt Becker in pulsFOG
Dear Dramm, I purchased a Dramm Revolver spray nozzle several months ago and it no longer works. It will not shut off when not in use, and the...
Started by David C. Streicher in General
In working with water treatment where monitoring dissolved oxygen levels, we have noticed that low DO can be responsible for plant growth problems...
Started by Kurt Becker in Dissolved Oxygen
Has anyone found a chemical that works well for aphids? I have been using the sprays I normally use with a hand sprayer and they haven't been working...
Started by Smccoard in pulsFOG
The maximum load on the MistTime valve outputs is 6va. The number of solenoids you can run on one output depends on the load for each valve. If you...
Started by Kurt Becker in MistTime Controller
live stock quote. Live Ventures Incorporated is a holding company for diversified businesses. Commencing in fiscal year 2015, we began a strategic...
Started by Jalal in News
The FM Series of foamers needs to be connected to an external air compressor to work. This compressor will drive an air pump to push the solution and...
The Turbo ULV output rate is dependent on the nozzle installed. Flow rates are below:
Started by Kurt Becker in Turbo ULV
I have a bad timer switch and the switch that is in the sprayer is a (SUL 189s) and the owners manual parts list states the part as (SUL 189h) Which...
Started by Scott in Autofog
The standard FM Foamers come with 25' of EPDM rubber hose. However, with higher CFM compressors, longer lengths, up to 75', will work. Dramm can...
The Coldfogger AR can handle more corrosive products such as hydrogen peroxide and peroxyaceitc acid. However, thorough cleaning is required to...
Supported videos include:
Please paste your code into the box below:
Facebook
We'll never post without your permission.